IO3656 Fiber-Optic Communication 9.0 credits

Fiberoptisk kommunikation

The high ways of the IT society are the optical fibers. An optical fiber can transport several tens of terabit per second over hundreds of kilometers. Fiber-optic communication is an established technique but is simultaneously in rapid technical development towards higher bit-rates and more complex networks. The course will give you the knowledge in order to understand both the fundamentals and the rapid development, that you as professional engineer can use the fiber optics efficiently. The course treats important devices as optical fibers, laser diodes, optical detectors, and receivers from physical and transmission system point of view. You will also learn how to optimise optical communication links and calculate the bit error rate. The course follows the undergraduate course IO2653 but includes also a project assignment where the student will design and simulate a fiber-optic system. The language is english.

  • Educational level

    Third cycle
  • Academic level (A-D)

    D
  • Subject area

  • Grade scale

Information for research students about course offerings

The course is given annually if there at least five undergraduate or graduate students have registered in advance for courses IO2653 and/or IO3656

Intended learning outcomes

Knowledge of fiber-optical components and systems with applications to communications. Parameters of devices that are relevant for the system performance are derived from physical descriptions, and form the input parameters for the design of fiber-optic links.
After a completed course, the participants should be able to:
- understand, describe, analyse, and compare the most important devices: optical transmitters, optical fibers, and optical detectors
- design digital fiber-optic links.
- simulate a multilevel coherent fiber-optic communication system using computer software

Course main content

Dielectric waveguides: Attenuation, wavelength dispersion, modes, fields.
Light sources and optical amplifiers: Semiconductor laser, light-emitting diode, rate equations, output power, modulation response, chirp, noise, optical amplifiers.
Detectors: PIN-diode, avalanche diode, responsivity, bandwidth, noise.
Transmission systems: Optical links, direct detection systems, soliton systems, coherent systems, multilevel signaling, dispersion limitations, attenuation limitations, additive noise, signal dependent noise, bit error rate, optical networks, simulation and design

Disposition

The course is given in a traditional way, i.e. with lectures (28h) followed by corresponding exercises (16h). There are also two laboratory works (2*4h) and one project assignment. The course follows the undergraduate course IO2653 but includes also a project assignment where the student will design and simulate a fiber-optic system. The language is English.

Eligibility

PhD student

It is anticipated that the students are acquainted with:
- Waveguides: Wave equation and the concept of modes. 
- Solid-state electronics: p-n-junction
- Circuit theory: Impulse response, convolution, transfer function of linear systems.
- Signal theory: Auto correlation function, power spectral density 

Recommended prerequisites

It is anticipated that the students are acquainted with:
- Waveguides: Wave equation and the concept of modes. 
- Solid-state electronics: p-n-junction
- Circuit theory: Impulse response, convolution, transfer function of linear systems.
- Signal theory: Auto correlation function, power spectral density

Literature

Fibre-Optic Communication Systems by Govind Agrawal, 4th edition, Wiley
Additional course material is possible to download from course webpage

Although 4th edition of the course book is recommended, also third edition of the book is possible to use

Required equipment

Calculator and access to a computer for the project assignment

Examination

The written examination is graded A-F. At least a grade C is necessary in this graduate course to get a passing grade on the exam. Calculator, mathematic handbook, the course book and the lecture notes (but NOT exercise notes) are allowed and recommended aids.

Requirements for final grade

To pass the entire course, at least a C is needed on the examination and a passing grade on the laborations and the project assignment.

Offered by

SCI/Applied Physics

Contact

Richard Schatz (rschatz@kth.se)

Examiner

Sergei Popov <sergeip@kth.se>

Supplementary information

The course follows the undergraduate course IO2653 but includes also a project assignment where the student will design and/or simulate a fiber-optic system.

Version

Course syllabus valid from: Autumn 2014.