Publications by Mats Åbom

Peer reviewed

Articles

[1]

S. Jacob et al., "Acoustic scattering in a small centrifugal compressor based on the use of linearized equations in a rotating frame," Journal of Sound and Vibration, vol. 544, pp. 117315-117315, 2023.

[2]

T. Zhong, C. Yang and M. Åbom, "Tonal noise reduction of an electric ducted fan using over-the-rotor acoustic treatment," Applied Acoustics, vol. 205, 2023.

[3]

M. Åbom and S. Jacob, "A comment on the correct boundary conditions for the Cremer impedance," JASA Express Letters, vol. 1, no. 2, 2021.

[4]

C. Yang et al., "Investigation of Extended-Tube Liners for Control of Low-Frequency Duct Noise," AIAA Journal, vol. 59, no. 10, pp. 4179-4194, 2021.

[5]

M. W. Nashed, T. Elnady and M. Åbom, "The effect of reflections in power-based models for sound in ducts," Proceedings of Meetings on Acoustics (POMA), vol. 30, 2021.

[6]

S. Sack and M. Åbom, "Acoustic plane-wave decomposition by means of multilayer perceptron neural networks," Journal of Sound and Vibration, vol. 486, 2020.

[7]

J. Zhou, M. Karlsson and M. Åbom, "Designing regenerators of thermoacoustic engines for automotive waste heat recovery," SAE technical paper series, no. April, 2020.

[8]

X. Qiu et al., "Mode-Merging Design Method for Nonlocally Reacting Liners with Porous Materials," AIAA Journal, vol. 58, no. 6, pp. 2533-2545, 2020.

[9]

X. Qiu et al., "Optimality analysis of bulk-reacting liners based on mode-merging design method," Journal of Sound and Vibration, vol. 485, 2020.

[10]

D.-Y. Kim, J.-G. Ih and M. Åbom, "Virtual Herschel-Quincke tube using the multiple small resonators and acoustic metamaterials," Journal of Sound and Vibration, vol. 466, 2020.

[11]

S. Baro et al., "Modelling of a lined tyre for predicting cavity noise mitigation," Applied Acoustics, vol. 155, pp. 391-400, 2019.

[12]

A. M. Netto Spillere et al., "Optimum Impedance in the Presence of an Inviscid Sheared Flow," AIAA Journal, vol. 57, no. 3, pp. 1044-1054, 2019.

[13]

J. Zhou, M. Karlsson and M. Åbom, "Study of thermoacoustic engine for automotive exhaust waste heat recovery," SAE technical paper series, vol. 2019-April, no. April, 2019.

[14]

Z. Zhang, H. Bodén and M. Åbom, "The Cremer impedance : An investigation of the low frequency behavior," Journal of Sound and Vibration, vol. 459, 2019.

[15]

E. Garnell, M. Åbom and G. Banwell, "The use of the two-port method to characterize high-speed small fans," Applied Acoustics, vol. 146, pp. 155-163, 2019.

[16]

A. Rynell et al., "A numerical study of noise characteristics originating from a shrouded subsonic automotive fan," Applied Acoustics, vol. 140, pp. 110-121, 2018.

[17]

Z. Zhang et al., "Experimental Analysis on the 'Exact' Cremer Impedance in Rectangular Ducts," SAE technical paper series, vol. 2018-June, no. June, 2018.

[18]

M. Shur et al., "Experimental/numerical study of ducted-fan noise : Effect of duct inlet shape," AIAA Journal, vol. 56, no. 3, pp. 979-996, 2018.

[19]

S. Vizzini et al., "Flow Noise Generation in a Pipe Bend," SAE technical paper series, vol. 2018-June, no. June, 2018.

[20]

R. Kabral and M. Åbom, "Investigation of turbocharger compressor surge inception by means of an acoustic two-port model," Journal of Sound and Vibration, vol. 412, pp. 270-286, 2018.

[21]

M. W. Nashed, T. Elnady and M. Åbom, "Modeling of duct acoustics in the high frequency range using two-ports," Applied Acoustics, vol. 135, pp. 37-47, 2018.

[22]

P. Williams et al., "Reducing low frequency tonal noise in large ducts using a hybrid reactive-dissipative silencer," Applied Acoustics, vol. 131, pp. 61-69, 2018.

[23]

M. Knutsson and M. Åbom, "Acoustic modeling of charge air coolers," Journal of Vibration and Acoustics-Transactions of the ASME, vol. 139, no. 4, 2017.

[24]

S. Sack and M. Åbom, "Investigation of orifice aeroacoustics by means of multi-port methods," Journal of Sound and Vibration, vol. 407, pp. 32-45, 2017.

[25]

S. Sack et al., "Numerical eduction of active multi-port data for in-duct obstructions," Journal of Sound and Vibration, vol. 411, pp. 328-345, 2017.

[26]

Z. Zhang et al., "Particle Number Reduction in Automotive Exhausts Using Acoustic Metamaterials," SAE International Journal of Engines, vol. 10, no. 4, pp. 1566-1572, 2017.

[27]

M. Karlsson et al., "A Note on the Applicability of Thermo-Acoustic Engines for Automotive Waste Heat Recovery," SAE International Journal of Materials & Manufacturing, vol. 9, no. 2, pp. 286-293, 2016.

[28]

A. Rynell et al., "Acoustic characteristics of a heavy duty vehicle cooling module," Applied Acoustics, vol. 111, pp. 67-76, 2016.

[29]

A. Okasha, T. Elnady and M. Åbom, "Analysis of pipeline networks using two-ports," Applied Acoustics, vol. 109, pp. 44-53, 2016.

[30]

S. Sack, M. Åbom and G. Efraimsson, "On Acoustic Multi-Port Characterisation Including Higher Order Modes," Acta Acoustica united with Acustica, vol. 192, no. 5, pp. 834-850, 2016.

[31]

R. Kabral et al., "Optimization of Compact Non-Fibrous Silencer for the Control of Compressor Noise," SAE technical paper series, vol. 2016-June, no. June, 2016.

[32]

R. Kabral, L. Du and M. Åbom, "Optimum Sound Attenuation in Flow Ducts Based on the "Exact" Cremer Impedance," Acta Acoustica united with Acustica, vol. 102, no. 5, pp. 851-860, 2016.

[33]

L. Du et al., "Sound amplification at a rectangular T-junction with merging mean flows," Journal of Sound and Vibration, vol. 367, pp. 69-83, 2016.

[34]

A. Holmberg, M. Karlsson and M. Åbom, "Aeroacoustics of rectangular T-junctions subject to combined grazing and bias flows - An experimental investigation," Journal of Sound and Vibration, vol. 340, pp. 152-166, 2015.

[35]

A. Hynninen and M. Åbom, "Determination of in-duct sound power beyond the plane wave range using wall-mounted microphones," Applied Acoustics, vol. 99, pp. 24-30, 2015.

[36]

L. Feng, M. Åbom and U. Orrenius, "Engineering methods to predict noise levels at reference points with known source properties," Applied Acoustics, vol. 96, pp. 68-74, 2015.

[37]

E. Alenius, M. Åbom and L. Fuchs, "Large eddy simulations of acoustic-flow interaction at an orifice plate," Journal of Sound and Vibration, vol. 345, pp. 162-177, 2015.

[38]

O. Kårekull, G. Efraimsson and M. Åbom, "Revisiting the Nelson-Morfey scaling law for flow noise from duct constrictions," Journal of Sound and Vibration, vol. 357, pp. 233-244, 2015.

[39]

M. A. Temiz et al., "The influence of edge geometry on end-correction coefficients in micro perforated plates," Journal of the Acoustical Society of America, vol. 138, no. 6, pp. 3668-3677, 2015.

[40]

R. Kabral et al., "A compact silencer for the control of compressor noise," SAE International Journal of Engines, vol. 7, no. 3, pp. 1572-1578, 2014.

[41]

A. Hynninen and M. Åbom, "Acoustic Source Characterization for Prediction of Medium Speed Diesel Engine Exhaust Noise," Journal of Vibration and Acoustics-Transactions of the ASME, vol. 136, no. 2, pp. 021008, 2014.

[42]

H. Tiikoja et al., "Experimental investigations of sound reflection from hot and subsonic flow duct termination," Journal of Sound and Vibration, vol. 333, no. 3, pp. 788-800, 2014.

[43]

S. Allam and M. Åbom, "Fan Noise Control Using Microperforated Splitter Silencers," Journal of Vibration and Acoustics-Transactions of the ASME, vol. 136, no. 3, pp. 031017, 2014.

[44]

O. Kårekull, G. Efraimsson and M. Åbom, "Prediction model of flow duct constriction noise," Applied Acoustics, vol. 82, pp. 45-52, 2014.

[45]

A. Hynninen and M. Åbom, "Simulation of the particle oxidation catalyst POC (R) acoustics," Noise Control Engineering Journal, vol. 62, no. 5, pp. 368-374, 2014.

[46]

T. Elnady, M. Åbom and Y. Yang, "Systematic Optimization of an Exhaust System to Meet Noise Radiation Criteria at Idle," SAE International Journal of Passenger Cars - Mechanical Systems, vol. 7, no. 3, 2014.

[47]

M. Åbom and R. Kabral, "Turbocharger noise - Generation and control," SAE technical paper series, vol. 2014, 2014.

[48]

R. Kabral, H. Rammal and M. Åbom, "Acoustical methods for investigating turbocharger flow instabilities," SAE technical paper series, vol. 4, pp. 2013-01-1879, 2013.

[49]

A. Hynninen et al., "Acoustic source data for medium speed IC-engines," Journal of Vibration and Acoustics-Transactions of the ASME, vol. 134, no. 5, pp. 051008, 2012.

[50]

S. Allam and M. Åbom, "Noise control for cooling fans on heavy vehicles," Noise Control Engineering Journal, vol. 60, no. 6, pp. 707-715, 2012.

[51]

A. Kierkegaard et al., "Simulations of whistling and the whistling potentiality of an in-duct orifice with linear aeroacoustics," Journal of Sound and Vibration, vol. 331, no. 5, pp. 1084-1096, 2012.

[52]

S. Allam and M. Åbom, "A New Type of Muffler Based on Microperforated Tubes," Journal of Vibration and Acoustics-Transactions of the ASME, vol. 133, no. 3, pp. 031005, 2011.

[53]

M. Knutsson et al., "A study on acoustical time-domain two-ports based on digital filters with application to automotive air intake systems," SAE International Journal of Passenger Cars - Mechanical Systems, vol. 4, no. 2, pp. 970-982, 2011.

[54]

M. Knutsson et al., "A study on acoustical time-domain two-ports based on digital filters with application to automotive air intake systems," SAE technical paper series, 2011.

[55]

M. Karlsson, M. Åbom and R. Glav, "Aeroacoustics of duct branches : with application to silencers," SAE technical paper series, 2011.

[56]

T. Elnady, S. Elsaadany and M. Åbom, "Flow and Pressure Drop Calculation Using Two-Ports," Journal of Vibration and Acoustics-Transactions of the ASME, vol. 133, no. 4, pp. 041016, 2011.

[57]

H. Tiikoja et al., "Investigations of automotive turbo-charger acoustics," SAE International Journal of Engines, vol. 4, no. 2, pp. 2531-2542, 2011.

[58]

H. Tiikoja et al., "Investigations of automotive turbocharger acoustics," SAE technical paper series, 2011.

[59]

M. Karlsson and M. Åbom, "On the Use of Linear Acoustic Multiports to Predict Whistling in Confined Flows," Acta Acoustica united with Acustica, vol. 97, no. 1, pp. 24-33, 2011.

[60]

M. Karlsson and M. Åbom, "Quasisteady model of the acoustic scattering of a T- Junction," Journal of Sound and Vibration, vol. 330, no. 21, pp. 5131-5137, 2011.

[61]

H. Tiikoja et al., "Sound transmission in automotive turbochargers," SAE technical paper series, 2011.

[62]

M. Karlsson and M. Åbom, "Aeroacoustics of T-junctions : An experimental investigation," Journal of Sound and Vibration, vol. 329, no. 10, pp. 1793-1808, 2010.

[63]

K. Bolin and M. Åbom, "Air-borne sound generated by sea waves," Journal of the Acoustical Society of America, vol. 127, no. 5, pp. 2771-2779, 2010.

[64]

T. Elnady, M. Åbom and S. Allam, "Modeling perforates in mufflers using two-ports," Journal of Vibration and Acoustics-Transactions of the ASME, vol. 132, no. 6, pp. 061010, 2010.

[65]

M. Knutsson and M. Åbom, "The effect of turbulence damping on acoustic wave propagation in tubes," Journal of Sound and Vibration, vol. 329, no. 22, pp. 4719-4739, 2010.

[66]

H. Rämmal and M. Åbom, "Experimental determination of sound transmission in turbo-compressors," SAE technical paper series, 2009.

[67]

M. Knutsson and M. Åbom, "Sound propagation in narrow tubes including effects of viscothermal and turbulent damping with application to charge air coolers," Journal of Sound and Vibration, vol. 320, pp. 289-321, 2009.

[68]

M. Karlsson, R. Glav and M. Åbom, "The Herschel-Quincke tube : The attenuation conditions and their sensitivity to mean flow," Journal of the Acoustical Society of America, vol. 124, no. 2, pp. 723-732, 2008.

[69]

M. Knutsson and M. Åbom, "Acoustic analysis of charge air coolers," SAE technical paper series, 2007.

[70]

H. Rämmal and M. Åbom, "Acoustics of turbochargers," SAE technical paper series, 2007.

[71]

H. Rämmal and M. Åbom, "Characterization of air terminal device noise using acoustic 1-port source models," Journal of Sound and Vibration, vol. 300, no. 05-mar, pp. 727-743, 2007.

[72]

S. Allam and M. Åbom, "Investigation of damping and radiation using full plane wave decomposition in ducts," Journal of Sound and Vibration, vol. 292, no. 05-mar, pp. 519-534, 2006.

[73]

S. Allam and M. Åbom, "Modeling and testing of after-treatment devices," Journal of Vibration and Acoustics-Transactions of the ASME, vol. 128, no. 3, pp. 347-356, 2006.

[74]

S. Allam and M. Åbom, "Sound propagation in an array of narrow porous channels with application to diesel particulate filters," Journal of Sound and Vibration, vol. 291, no. 05-mar, pp. 882-901, 2006.

[75]

S. Allam and M. Åbom, "Acoustic modelling and testing of diesel particulate filters," Journal of Sound and Vibration, vol. 288, no. 02-jan, pp. 255-273, 2005.

[76]

R. Glav, P.-L. Regaud and M. Åbom, "Study of a folded resonator including the effects of higher order modes," Journal of Sound and Vibration, vol. 273, no. 4-5, pp. 777-792, 2004.

[77]

R. Glav and M. Åbom, "A general formalism for analysing acoustic 2-port networks," Journal of Sound and Vibration, vol. 202, no. 5, pp. 739-747, 1997.

Conference papers

[78]

A. G. Pietroniro et al., "HVAC Blower : A Steady State RANS Noise Prediction Method," in 13th International Styrian Noise, Vibration and Harshness Congress: The European Automotive Noise Conference, SNVH 2024, 2024.

[79]

P. Ulfvengren et al., "Noise simulation for UAM integration : Application to a health-care logistics system. DICUAM conf, 2024 Amsterdam," in DICUAM 2024 Amsterdam, 2024.

[80]

P. Ulfvengren et al., "UAM system integration : system analysis and noise simulations in support of regional and city planning," in DICUAM 2024, 2024.

[81]

S. Jacob and M. Åbom, "Acoustic Scattering Computations for High-Speed Rotors using Rotating Reference Frames," in Forum Acusticum 2023 - 10th Convention of the European Acoustics Association, EAA 2023, 2023.

[82]

J. Wang et al., "Low-frequency Broadband Noise Absorption of Multi-chamber Micro-perforated Panel Absorbers in Normal and Grazing Acoustic Incidence," in AIAA Aviation and Aeronautics Forum and Exposition, AIAA AVIATION Forum 2023, 2023.

[83]

I. L. Arteaga et al., "The TRANSIT project: innovation towards train pass-by noise source characterisation and separation tools," in 2022 Conference Proceedings Transport Research Arena, TRA Lisbon 2022, 2023, pp. 989-996.

[84]

T. Zhong, C. Yang and M. Åbom, "A compact tonal noise control solution to an electric ducted fan," in 24th International Congress on Acoustics, ICA 2022 : Proceedings, 2022.

[85]

A. G. Pietroniro et al., "Effects of Boundary Layer and Local Volumetric Cells Refinements on Compressor Direct Noise Computation," in SAE Technical Papers, 2022.

[86]

K. Bolin, S. Jacob and M. Åbom, "Improved methods for source characterization on trains," in Internoise 2022 : 51st International Congress and Exposition on Noise Control Engineering, 2022.

[87]

A. Aulitto et al., "Noise control in HVAC systems with ultra-thin low-frequency (UTLF) absorbers," in Proceedings of ISMA 2022 - International Conference on Noise and Vibration Engineering and USD 2022 - International Conference on Uncertainty in Structural Dynamics, 2022, pp. 365-374.

[88]

Y. Lai et al., "Study of Installation Effects on Automotive Cooling Fan Noise," in SAE Technical Papers, 2022.

[89]

J. Zhou et al., "Designing Thermoacoustic Engines for Automotive Exhaust Waste Heat Recovery," in SAE Technical Papers, 2021.

[90]

P. T. Williams et al., "Hybrid dissipative/reactive silencer predictions with comparison to measurement," in Euronoise 2015, 2020, pp. 2243-2248.

[91]

C. Yang et al., "Low frequency duct noise control using extended tube liners," in AIAA AVIATION 2020 FORUM, 2020.

[92]

U. Orrenius, L. Feng and M. Åbom, "Rail vehicle source models within a virtual certification process," in Euronoise 2015, 2020, pp. 2043-2048.

[93]

U. Tengzelius and M. Åbom, "Aircraft pass-by noise on ground modelled with the SAFT-program," in INTER-NOISE 2019 MADRID - 48th International Congress and Exhibition on Noise Control Engineering, 2019.

[94]

X. Qiu et al., "Mode merging design method for non-locally reacting liner with porous bulk materials," in 25th AIAA/CEAS Aeroacoustics Conference, 2019, 2019.

[95]

Z. Zhang et al., "Recent development in the cremer impedance : concept extension, experimental analysis and numerical validation," in 25th AIAA/CEAS Aeroacoustics Conference, 2019, 2019.

[96]

Y. Meng et al., "Semi-empirical impedance model of perforated plate under grazing flow," in 25th AIAA/CEAS Aeroacoustics Conference, 2019, 2019.

[97]

Z. Zhang, M. Åbom and H. Bodén, "The cremer impedance for double-lined rectangular ducts," in INTER-NOISE 2019 MADRID - 48th International Congress and Exhibition on Noise Control Engineering, 2019.

[98]

S. Sack and M. Åbom, "Trained algorithms for mode decomposition in ducts," in Proceedings of the International Congress on Acoustics, 2019, pp. 5292-5298.

[99]

A. G. Pietroniro et al., "A Steady-State Based Investigation of Automotive Turbocharger Compressor Noise," in SAE Technical Papers, 2018.

[100]

Q. Xianghai et al., "A combined design method for optimal acoustic treatment of annular aeroengine inlet based on cremer impedance," in 25th International Congress on Sound and Vibration 2018, ICSV 2018 : Hiroshima Calling, 2018, pp. 1248-1255.

[101]

J. Lemne, S. Sack and M. Åbom, "Acoustics of micro-perforated orifice plates," in INTER-NOISE 2018 - 47th International Congress and Exposition on Noise Control Engineering : Impact of Noise Control Engineering, 2018.

[102]

M. Åbom, K. Bolin and P. Ulfvengren, "Air traffic management and noise," in INTER-NOISE 2018 - 47th International Congress and Exposition on Noise Control Engineering : Impact of Noise Control Engineering, 2018.

[103]

M. W. Nashed, T. Elnady and M. Åbom, "Effect of reflections on HVAC systems power-based acoustic simulation," in INTER-NOISE 2018 - 47th International Congress and Exposition on Noise Control Engineering : Impact of Noise Control Engineering, 2018.

[104]

Z. Zhang et al., "Experimental analysis of whistle noise in a particle agglomeration pipe," in INTER-NOISE 2018 - 47th International Congress and Exposition on Noise Control Engineering : Impact of Noise Control Engineering, 2018.

[105]

Z. Zhang et al., "Investigation of the 'exact' cremer impedance," in 25th International Congress on Sound and Vibration 2018, ICSV 2018 : Hiroshima Calling, 2018, pp. 1810-1817.

[106]

A. M. N. Spillere et al., "Optimum impedance in the presence of an inviscid sheared flow," in 2018 AIAA/CEAS Aeroacoustics Conference, 2018.

[107]

M. W. Nashed, T. Elnady and M. Åbom, "Review of splitter silencer modeling techniques," in Euronoise 2018, 2018, pp. 2285-2292.

[108]

M. Karlsson, M. Åbom and M. Knutsson, "Stop Whistling! : A Note on Fluid Driven Whistles in Flow Ducts," in SAE Technical Papers, 2018.

[109]

D. -. Kim et al., "A virtual herschel-quincke tube using slow sound," in INTER-NOISE 2017 - 46th International Congress and Exposition on Noise Control Engineering : Taming Noise and Moving Quiet, 2017.

[110]

P. T. Williams et al., "Circular duct hybrid bar silencer insertion loss measurement with comparison to prediction," in INTER-NOISE 2017 - 46th International Congress and Exposition on Noise Control Engineering : Taming Noise and Moving Quiet, 2017.

[111]

Y. El Nemr et al., "Experimental investigation of transmission loss in an automotive turbocharger compressor under ideal and real engine operating conditions," in 12th European Conference on Turbomachinery Fluid Dynamics and Thermodynamics, ETC 2017, 2017.

[112]

C. Schram et al., "Innovative noise control in ducts," in 23rd AIAA/CEAS Aeroacoustics Conference, 2017, 2017.

[113]

Z. Zhang et al., "Revisiting the cremer impedance," in Proceedings of Meetings on Acoustics, 2017.

[114]

P. T. Williams et al., "The influence of higher order incident modes on the performance of a hybrid reactive-dissipative splitter silencer," in Proceedings of Meetings on Acoustics, 2017.

[115]

M. Shur et al., "Effect of inlet distortions on ducted fan noise," in 22nd AIAA/CEAS Aeroacoustics Conference, 2016, 2016.

[116]

S. Sack and M. Åbom, "Full multi-port characterization of a circular orifice plate," in 22nd AIAA/CEAS Aeroacoustics Conference, 2016, 2016.

[117]

M. Farooqui, T. Elnady and M. Åbom, "Measurement of perforate impedance with grazing flow on both sides," in 22nd AIAA/CEAS Aeroacoustics Conference. American Institute of Aeronautics and Astronautics., 2016.

[118]

S. Sack and M. Åbom, "Modal Filters for Mitigation of In-duct Sound," in Proceedings of Meetings on Acoustics, 2016.

[119]

S. Sack and M. Åbom, "Modal filters for in-duct sound based on the cremer impedance and micro-perforated plates," in Proceedings of the INTER-NOISE 2016 - 45th International Congress and Exposition on Noise Control Engineering : Towards a Quieter Future, 2016, pp. 3215-3222.

[120]

L. Du et al., "Modelling of Acoustic Resonators Using the Linearized Navier Stokes Equations," in 9th International Styrian Noise, Vibration and Harshness Congress: The European Automotive Noise Conference, ISNVH 2016, 2016.

[121]

L. Du, M. Karlsson and M. Åbom, "Numerical study on the sound amplification of a T-junction with bias flow," in Springer Proceedings in Physics, 2016, pp. 373-381.

[122]

M. Karlsson, M. Knutsson and M. Åbom, "Predicting Fluid Driven Whistles in Automotive Intake and Exhaust Systems," in 9th International Styrian Noise, Vibration and Harshness Congress: The European Automotive Noise Conference, ISNVH 2016; Grazer CongressSparkassenplatz 1Graz; Austria; 22 June 2016 through 24 June 2016, 2016.

[123]

S. Baro, R. Corradi and M. Åbom, "Tyre cavity noise : Porous materials as a countermeasure," in Proceedings of the INTER-NOISE 2016 - 45th International Congress and Exposition on Noise Control Engineering : Towards a Quieter Future, 2016, pp. 2313-2318.

[124]

M. Lalit, M. Karlsson and M. Åbom, "AN ENGINEERING NON-LINEAR MODEL FOR THERMO-ACOUSTIC ENGINES," in PROCEEDINGS OF THE 22ND INTERNATIONAL CONGRESS ON SOUND AND VIBRATION : MAJOR CHALLENGES IN ACOUSTICS, NOISE AND VIBRATION RESEARCH, 2015, 2015.

[125]

O. Kårekull, G. Efraimsson and M. Åbom, "CHALLENGES AND OPPORTUNITIES FOR FLOW NOISE PREDICTION IN HVAC SYSTEMS," in INTERNATIONAL CONFERENCE ON FAN NOISE, TECHNOLOGY AND NUMERICAL METHODS, 15-17 APRIL 2015 L’Espace Tête d’Or, Lyon, France, 2015.

[126]

S. Allam and M. Åbom, "Noise reduction for automotive radiator cooling fans," in FAN 2015 - International Conference on Fan Noise, Technology and Numerical Methods, 2015.

[127]

A. Hynninen and M. Åbom, "Procedure to estimate the acoustic performance of the particle oxidation catalyst poc® with low Mach-number flows," in INTER-NOISE 2015 - 44th International Congress and Exposition on Noise Control Engineering, 2015.

[128]

S. Sack and Å. Mats, "Uncertainty estimation in multi-port measurements," in EuroNoise2015, the 10th European Congress and Exposition on Noise Control Engineering,Maastricht, Holland, May 31 - June 3, 2015.

[129]

M. A. Temiz et al., "Acoustic end correction in micro-perforated plates - Revisited," in 21st International Congress on Sound and Vibration 2014, ICSV 2014, 2014, pp. 1203-1209.

[130]

A. Hynninen and M. Åbom, "Acoustic two-port simulation model for the particle oxidation catalyst (POC®)," in INTERNOISE 2014 - 43rd International Congress on Noise Control Engineering : Improving the World Through Noise Control, 2014.

[131]

A. Rynell et al., "Acoustical Broadband signatures from RANS Turbulence Quantities," in The 21st International Congress on Sound and Vibration, 2014, pp. 1541-1548.

[132]

M. Wagih, T. Elnady and M. Åbom, "Analysis of Flow and Sound Propagation in HVAC Ducts Using Two-Port Network Theory," in ASHRAE TRANSACTIONS 2014, VOL 120, PT 2, 2014.

[133]

S. Sack and Å. Mats, "Experimental characterization of acoustic multi-ports," in Forum Acusticum paper, 2014.

[134]

S. Sack et al., "Generation and scattering of acoustic modes in ducts with flow," in 20th AIAA/CEAS Aeroacoustics Conference, 2014.

[135]

R. Kabral and M. Åbom, "Investigation of flow-acoustic interaction in automotive turbocharger," in Proceedings of ISMA 2014 - International Conference on Noise and Vibration Engineering and USD 2014 - International Conference on Uncertainty in Structural Dynamics, 2014, pp. 1327-1331.

[136]

U. Orrenius et al., "Rail vehicle source assessment within a virtual certification process," in PROCEEDINGS OF INTERNATIONAL CONFERENCE ON NOISE AND VIBRATION ENGINEERING (ISMA2014) AND INTERNATIONAL CONFERENCE ON UNCERTAINTY IN STRUCTURAL DYNAMICS (USD2014), 2014, pp. 3511-3525.

[137]

L. Du and M. Åbom, "Using micro-perforated plates to realize a silencer based on the Cremer impedance," in Proceedings of Forum Acusticum, 2014.

[138]

A. Okasha, T. Elnady and M. Åbom, "Acoustic response analysis of pipeline networks using two-ports," in 42nd International Congress and Exposition on Noise Control Engineering 2013, INTER-NOISE 2013 : Noise Control for Quality of Life, 2013, pp. 5857-5866.

[139]

J. Jansson et al., "Adaptive stabilized finite element framework for simulation of vocal fold turbulent fluid-structure interaction," in Proceedings of Meetings on Acoustics : Volume 19, 2013, 2013, pp. 1-9.

[140]

A. Holmberg, M. Åbom and M. Karlsson, "Aeroacoustics of rectangular T-junctions subject to combined grazing and bias flows - An experimental investigation," in 19th AIAA/CEAS Aeroacoustics Conference, 2013.

[141]

M. Wagih, T. Elnady and M. Åbom, "Analysis of duct networks at high frequencies using two-ports," in 42nd International Congress and Exposition on Noise Control Engineering 2013, INTER-NOISE 2013 : Noise Control for Quality of Life, 2013, pp. 5896-5905.

[142]

M. Åbom and S. Allam, "Dissipative silencers based on micro-perforated plates," in SAE Technical Papers, 2013.

[143]

A. Hynninen and M. Åbom, "Estimating the high frequency in-duct sound power using sound pressures at the duct wall," in 20th International Congress on Sound and Vibration 2013, ICSV 2013 : Volume 3, 2013, 2013, pp. 2553-2559.

[144]

S. Allam and M. Åbom, "Investigation of aerodynamic installation effects for an axial fan," in 19th AIAA/CEAS Aeroacoustics Conference, 2013.

[145]

A. Rynell et al., "Quiet and efficient cooling for IC-engine powered systems," in 42nd International Congress and Exposition on Noise Control Engineering 2013, INTER-NOISE 2013 : Noise Control for Quality of Life, 2013, pp. 5677-5686.

[146]

S. Allam and M. Åbom, "Whistling potential for duct components," in SAE Technical Papers : Volume 4, 2013, 2013, p. 2013-01-1889.

[147]

S. Allam and M. Åbom, "Acoustic modelling and characterization of plate heat exchangers," in SAE Technical Paper 2012-01-1562, 2012.

[148]

S. Allam and M. Åbom, "Cooling fan noise control using micro-perforates," in Int. Congr. Expos. Noise Control Eng., INTER-NOISE, 2012, pp. 10434-10445.

[149]

T. Elnady, W. Elsahar and M. Åbom, "Estimation of temperature drop in exhaust systems," in 41st International Congress and Exposition on Noise Control Engineering 2012, INTER-NOISE 2012 : Volume 11, 2012, 2012, pp. 9362-9375.

[150]

E. Alenius, M. Åbom and L. Fuchs, "LES of acoustic-flow interaction at an orifice plate," in 18th AIAA/CEAS Aeroacoustics Conference (33rd AIAA Aeroacoustics Conference), 2012.

[151]

M. Knutsson and M. Åbom, "Low frequency damping from turbulence with application to charge air coolers," in Int. Congr. Expos. Noise Control Eng., INTER-NOISE, 2012, pp. 9424-9433.

[152]

A. Hynninen and M. Åbom, "Procedure to estimate the in-duct sound power in the high frequency range with non-plane waves," in ASME 2012 Noise Control and Acoustics Division Conference at InterNoise 2012, 2012, pp. 181-191.

[153]

A. Hynninen and M. Åbom, "Procedure to estimate the in-duct sound power in the high frequency range with non-plane waves," in 41st International Congress and Exposition on Noise Control Engineering 2012, INTER-NOISE 2012 : Volume 10, 2012, 2012, pp. 8026-8036.

[154]

A. Hynninen et al., "Acoustic source data for medium speed IC-engines," in 18th International Congress on Sound and Vibration 2011 (ICSV 18), 2011, pp. 811-818.

[155]

A. M. Pedrosa et al., "Experimental measurement of acoustic properties by a two source method with simultaneous excitation," in 18th International Congress on Sound and Vibration 2011, ICSV 2011, 2011, pp. 879-886.

[156]

E. Alenius, M. Åbom and L. Fuchs, "Scattering of Plane Waves by a Constriction," in Proceedings of ASME Turbo Expo 2011, Vol 7, Parts A-C, 2011, pp. 1043-1052.

[157]

H. Tiikoja et al., "Sound transmission in automotive turbochargers," in Noise and Vibration Conference and Exhibition (SAE NVH 2011)Grand Rapids, Michigan, USA, May 2011, 2011.

[158]

S. Elsaadany et al., "ACOUSTIC RESPONSE ANALYSIS OF OIL & GAS PIPELINE NETWORKS TO PREVENT THEIR FATIGUE AND FAILURE," in PROCEEDINGS OF THE 17TH INTERNATIONAL CONGRESS ON SOUND AND VIBRATION, 2010.

[159]

M. Åbom, "Acoustic multi-ports with application to duct acoustics," in 17th International Congress on Sound and Vibration 2010, ICSV 2010 : Volume 5, 2010, pp. 3930-3942.

[160]

M. Åbom and M. Karlsson, "Can acoustic multi-port models be used to predict whistling," in 16th AIAA/CEAS Aeroacoustics Conference (31st AIAA Aeroacoustics Conference), 2010, p. 2010-4009.

[161]

H. Rämmal et al., "Experimental facility for the complete determination of sound transmission in turbochargers," in SAE Technical Papers, 2010, p. SAE Technical Paper 2010-01-1424.

[162]

P. Bournobuke and M. Åbom, "Flow acoustic analysis at ciclope," in 17th International Congress on Sound and Vibration 2010, ICSV 2010, 2010, pp. 1068-1080.

[163]

M. Karlsson and M. Åbom, "Linear stability analysis applied to flow duct acoustics," in 20th International Congress on Acoustics 2010, ICA 2010 - Incorporating Proceedings of the 2010 Annual Conference of the Australian Acoustical Society : Volume 1, 2010, pp. 182-185.

[164]

S. Allam and M. Åbom, "On optimal design of mufflers using micro-perforated panels," in 17th International Congress on Sound and Vibration 2010, ICSV 2010 : Volume 2, 2010, pp. 1158-1165.

[165]

S. Boij, M. Åbom and R. Pieters, "Reflection properties of a flow pipe with a small angle diffuser outlet," in 17th International Congress on Sound and Vibration 2010, ICSV 2010 : Volume 1, 2010, pp. 706-712.

[166]

H. Tiikoja et al., "Test-rig for complete acoustic characterization of turbochargers," in 16th AIAA/CEAS Aeroacoustics Conference (31st AIAA Aeroacoustics Conference), 2010.

[167]

A. Holmberg, H. Bodén and M. Åbom, "The Error Suppression of an Experimental Over-Determination of In-Duct Flow Noise Sources," in 16th AIAA/CEAS Aeroacoustics Conference, Stockholm, June 2010, 2010, pp. 1-19.

[168]

H. Rämmal and M. Åbom, "Experimental Determination of Sound Transmission Through Turbo-Compressors," in SAE Technical Paper, no. 2009- 01-2045. May, 2009, 2009.

[169]

M. Åbom, M. Karlsson and A. Kierkegaard, "On the use of linear aero-acoustic methods to predict whistling," in 16th International Congress on Sound and Vibration 2009, ICSV 2009, 2009, pp. 2406-2413.

[170]

Y. Jiang and M. Åbom, "Acoustic Modeling of Heat Exchangers," in 37th International Congress and Exposition on Noise Control Engineering (inter-noise 2008), Shanghai, China. 26-29 October 2008, 2008.

[171]

S. Allam and M. Åbom, "Experimental characterization of acoustic liners with extended reaction," in 14th AIAA/CEAS Aeroacoustics Conference (29th AIAA Aeroacoustics Conference), 2008.

[172]

M. Karlsson et al., "Experimental determination of the aero-acoustic properties of an in-duct flexible plate," in 14th AIAA/CEAS Aeroacoustics Conference (29th AIAA Aeroacoustics Conference), 2008.

[173]

T. Elnady, S. Elsaadany and M. Åbom, "Flow and pressure drop calculation using two-ports," in Int. Congr. Sound Vib., ICSV, 2008, pp. 743-750.

[174]

Y. Guo, S. Allam and M. Åbom, "Micro-Perforated Plates for Vehicle Applications," in Proceedings of the 2008 Congress and exposition of noise control engineering, Inter-Noise 2008, 26-29 Oct, Shanghai, China, 2008.

[175]

H. Rämmal and M. Åbom, "Testrig for characterization of turbo-compressor acoustic properties," in 14th AIAA/CEAS Aeroacoustics Conference (29th AIAA Aeroacoustics Conference), 2008.

[176]

S. Allam and M. Åbom, "Aeroacoustic investigation of diaphragm orifices in ducts," in Turkish Acoustical Society - 36th International Congress and Exhibition on Noise Control Engineering, INTER-NOISE 2007 ISTANBUL, 2007, pp. 292-301.

[177]

Y. Guo et al., "Experimental Investigation of Acoustic Properties of Mufflers with Perforated Pipes," in 19^th International Congress on Acoustics Madrid, Spain, September 2007, 2007.

[178]

Y. Jiang et al., "Investigation of sound generation from an axial fan for engine cooling," in , 2007.

[179]

M. Knutsson and M. Åbom, "Sound propagation in narrow channels with arbitrary cross sections and superimposed mean flow with application to charge air coolers," in 14th International Congress on Sound and Vibration 2007, ICSV 2007, 2007, pp. 2633-2640.

[180]

S. Allam and M. Åbom, "Acoustic modeling and testing of a complex car muffler," in International Congress on Sound and Vibration 2006, 2006, pp. 1119-1126.

[181]

R. Glav, M. Åbom and R. Fairbrother, "Acoustic modelling for practical intake and exhaust system design," in 4:th International Styrian Noise, Vibration and Harshness Congress, Graz, Austria, 2006.

[182]

S. Allam and M. Åbom, "Advanced experimental procedure for in-duct aero-acoustics," in 13th International Congress on Sound and Vibration 2006, ICSV 2006, 2006, pp. 1185-1192.

[183]

M. Åbom, S. Allam and S. Boij, "Aero-acoustics of flow duct singularities at low mach numbers," in Collection of Technical Papers - 12th AIAA/CEAS Aeroacoustics Conference, 2006, pp. 3708-3717.

[184]

A. Kierkegaard et al., "Identifications of sources of sound in low Mach number flows by the use of flow field eigenmodes," in 13th International Congress on Sound and Vibration 2006, 2006, pp. 2967-2974.

[185]

G. Larsson et al., "Reducing engine noise with an enclosure using micro perforated plate," in EURONOISE - Eur. Conf. Noise Control: Adv. Solutions Noise Control, 2006.

[186]

T. Elnady and M. Åbom, "SIDLAB : New 1D sound propagation simulation software for complex duct networks," in 13th International Congress on Sound and Vibration 2006, 2006, pp. 4262-4269.

[187]

F. Ducret, F. Jacobsen and M. Åbom, "Development of micro-perforated acoustic elements for vehicle applications," in 12th International Congress on Sound and Vibration 2005 : ICSV 2005, 2005, pp. 2343-2350.

[188]

S. Allam and M. Åbom, "Diesel engines after treatment devices : Acoustic modeling," in 12th International Congress on Sound and Vibration 2005 : ICSV 2005, 2005, pp. 2358-2365.

[189]

C. -. Johansson et al., "Exhaust noise - A new novel in-situ measurement technology in duct," in 12th International Congress on Sound and Vibration 2005 : ICSV 2005, 2005, pp. 1639-1648.

[190]

T. Elnady and M. Åbom, "Modelling perforates in mufflers using two-ports," in 12th International Congress on Sound and Vibration 2005 : ICSV 2005, 2005, pp. 2294-2301.

[191]

R. Glav, A. Costa and M. Åbom, "Application of the folded resonator," in Proceedings of the Tenth International Congress on Sound and Vibration, 2003, pp. 3203-3210.

[192]

P.-O. Berglund, M. Åbom and L. Feng, "An application of the noise synthesis technology (NST) to a system with an axial fan," in Forum Acustica 2002, Seville, Spain, 2002.

[193]

R. Glav, H. Bodén and M. Åbom, "An acoustic model for automobile catalytic converters," in Inter-Noise, 1988, p. 1261-1266.

Chapters in books

[194]

H. D. Baumann and M. Åbom, "Valve-Induced Noise : Its Cause and Abatement," in Handbook of Noise and Vibration Control, Malcolm Crocker Ed., : John Wiley & Sons, 2008, pp. 935-945.

Other

[195]

A. Hynninen and M. Åbom, "Acoustic Simulation of Medium Speed IC-Engine Exhaust Gas After Treatment Devices with Substrate," SAE International, 2014.

Non-peer reviewed

Articles

[196]

A. Holmberg, M. Åbom and H. Bodén, "Accurate experimental two-port analysis of flow generated sound," Journal of Sound and Vibration, vol. 330, no. 26, pp. 6336-6354, 2011.

Conference papers

[197]

A. G. Pietroniro et al., "Propagation and Reflection Properties of Computational Setups for Radial Compressor Direct Noise Computation," in Forum Acusticum, 2020.

[198]

R. Kabral et al., "Experimental acoustic characterization of automotive twin-scroll turbine," in 12th European Conference on Turbomachinery Fluid Dynamics and Thermodynamics, ETC 2017, 2017.

[199]

A. Kierkegaard, M. Åbom and G. Efraimsson, "FREQUENCY-DOMAIN LINEARIZED NAVIER-STOKES EQUATIONS FOR FLOWDUCT COMPUTATIONAL AEROACOUSTICS," in NOVEM 2012, 1-4 April, Sorrento 2012, 2012.

[200]

H. Bodén et al., "Experimental Techniques for Aeroacoustics in Low Mach Number Confined Flows : Keynote Paper," in Proceedings of the International Conference on Mechanical Engineering 2011(ICME2011) 18-20 December 2011, Dhaka, Bangladesh, 2011.

[201]

S. Elsaadany et al., "Optimization of exhaust systems to meet the acoustic regulations and the enginespecifications," in 18th International Congressof Sound and Vibration, Rio De Janeiro (2011), 2011.

[202]

S. Elsaadany et al., "Insight into exhaust systems optimization techniques," in 17th International Congress of Sound and Vibration, Cairo (2010), 2010.

[203]

A. Kierkegaard et al., "Simulations of the Whistling Potentiality of an In-Duct Orifice with Linear Aeroacoustics," in 16th AIAA/CEAS Aeroacoustics Conference, Stockholm, Sweden, June 7-9, 2010, 2010.

[204]

T. Elnady, S. Elsaadany and M. Åbom, "Investigation into modeling of multi-perforated mufflers," in 16th International Congress of Sound and Vibration, Krakow (2009), 2009.

[205]

G. Efraimsson et al., "Simulation of Wave Scattering at an Orifice by using a Navier-Stokes Solver," in 13th AIAA/CEAS Aeroacoustics Conference (28th AIAA Aeroacoustics Conference) , Rome, Italy, May 21-23, 2007, 2007.

[206]

S. Allam, H. Bodén and M. Åbom, "Over-determination in acoustic two-port data measurement," in ICSV13-Vienna, 2006.